FGSW-2620PVM

24-Port 10/100Mbps + 2- Gigabit TP/SFP Managed PoE Switch

Overview

Cost effective 24 Ports Power over Ethernet with Enhanced Features for SMB PoE Networking
The PLANET FGSW-2620PVM PoE Switch features 802.3af Power over Ethernet (PoE) function, which optimizes the installation and safe power management of network devices such as wireless access points (AP), Voice over IP (VoIP) phones and IP Surveillance cameras. 802.3af PoE capabilities reduce installation costs of add-in network productivity devices. It frees the wireless AP deployment from restrictions of power outlet locations. With PoE features, power and data switching are integrated into one unit and delivered over a single cable, eliminating costs for additional AC wiring and reducing installation time. It provides a compact, affordable, safe and reliable power solution for small to medium enterprises.

Power over Ethernet, Easy Cabling installation
The PoE in-line power following the standard IEEE 802.3af makes the FGSW-2620PVM able to power on 24 PoE compliant devices at the distance up to 100 meters through the 4-pair Cat 5/5e UTP wire. With data and power over Ethernet from one unit, the FGSW-2620PVM shall reduce cables deployment and eliminates the need for dedicated electrical outlets on the wall, ceiling or any unreachable place. A wire carries both data and power lowering the installation costs, simplifying the installation effort and eliminating the need for electricians or extension cords. It is also proud of the key feature – energy saving. With more efficient switching power supply, the efficiency of the FGSW-2620PVM would be much better than four linear power adapters in a long run.

Centralized Power Distribution with Remote Management
The remote PoE management functions of FGSW-2620PVM make it easy to survey and control the PoE power provision to the devices and ensure interoperability with equipment from other vendors. Via Web interface, SNMP trap and SNMP monitoring, the manager can get the PoE devices status and alert immediately. The over-temperature detection of the PoE Switch offers a safe and stable PoE operating by limit the output power according to detected temperature to prevent destructive breakdown caused by un-expected overheating.

High Performance Wire-Speed Switching
The PLANET FGSW-2620PVM offers 24 10/100Mbps Fast Ethernet ports and 2 Gigabit TP/SFP combo ports. The two Gigabit TP/SFP combo ports can be either 1000Base-T for 10/100/1000Mbps or 1000Base-SX/LX through SFP (Small Factor Pluggable) interface. PLANET FGSW-2620PVM boasts a high performance switch architecture that is capable of providing non-blocking switch fabric and wire-speed throughput as high as 8.8Gbps. Its two built-in GbE uplink ports also offer incredible extensibility, flexibility and connectivity to the Core switch or Servers.

Efficient Management
Afford the current network to grow and expand, the PLANET FGSW-2620PVM provides console and telnetcommand line interface, advanced WEB and SNMP management interface to fill this kind of demand. With its built-in Web-based management, the FGSW-2620PVM offers an easy-to-use, platform-independent management and configuration facility. The FGSW-2620PVM supports standard Simple Network Management Protocol (SNMP) and can be monitored via any standard-based management software. For text-based management, the FGSW-2620PVM can also be accessed via Telnet and the console port. Moreover, the FGSW-2620PVM offers secure remote management by supporting Secure Socket Layer (SSL) connection which encrypts the packet content at each session.

Robust Layer 2 Features
For efficient management, via WEB interface, the FGSW-2620PVM can be programmed for basic switch management functions such as port speed configuration, Port link aggregation, IEEE 802.1Q VLAN and Q-in-Q VLAN, Port Mirroring, Rapid Spanning Tree and ACL security. Additionally, the firmware includes advanced features such as IGMP snooping, QoS (Quality of Service), broadcast storm and bandwidth control, to enhance bandwidth utilization.

Advanced Security and Quality of Service
The PLANET FGSW-2620PVM offers comprehensive Layer 2, Layer 3 and Layer 4 Access Control List (ACL) to filter out unwanted traffic. Its protection mechanisms comprises of RADIUS and Port-based 802.1X user and device authentication. Moreover, the switch provides MAC filter, Static MAC, IP/MAC binding and Port Securityfor enforcing security policies to the edge. The administrators can now construct highly secured corporate networks with considerably less time and effort than before.

To ensure IP voice and video communication get the quality of service needed, the FGSW-2620PVM classifies traffic and prioritizes Layer 2 802.1p or Layer 3 IP DSCP traffic into four hardware queues that support strict or Weighted Round Robin (WRR) queuing algorithms. It also empowers the SMB IP office to take full advantages of the limited network resources and guarantees the best performance in VoIP and Video conferencing transmission.
Ordering Information
FGSW-2620PVM 24-Port 10/100Mbps +2 Gigabit TP/SFP Combo Managed PoE Switch

Application

PoE IP Telephony Office
With the business office expansion, the additional telephones required could be installed in less cost via the implementation of PoE IP Telephony system than that of the traditional circuit wiring telephony system. PLANET FGSW-2620PVM PoE Managed Switch helps SMB to create an integrated data, voice, and powered network. PLANET 802.3af compliant IP Phones can be installed without the need of additional power cables because the power can be provided from the standard Ethernet cable connecting to the FGSW-2620PVM. PoE IP Phones and Analog Telephony Adapter work perfectly with the FGSW-2620PVM which injects power through the Ethernet cables and the IP DSCP priority of QoS feature improves the voice communicating. With FGSW-2620PVM, IP Telephony deployment becomes more reliable and cost effective, which helps SMB save tremendous cost when upgrading from the traditional telephony to IP Telephony communications infrastructure.
Department / Workgroup PoE Switch
Providing up to 24 PoE, in-line power interface, the FGSW-2620PVM Managed PoE Switch can easily build a power central-controlled IP phone system, IP camera system, or Wireless AP group for the enterprises. For instance, 24 cameras or APs can be easily installed in the company for surveillance demands or building a wireless roaming environment in the office. Without the power-socket limitation, the PoE Switch makes the installation of cameras or WLAN AP more easily and efficiently.
Factory / Warehouse Applications
While video surveillance system becomes more and more important for visible security in the factory or warehouse, the IP cameras with PoE function would be a lot helpful for the surveillance deployment when the power outlet not easily found in the ceiling or in the outdoor. For example, in the factory operation or in the warehouse storage security, the PoE IP cameras can be installed anywhere when needed regardless of the restrictions of power outlet location. With the PoE Switch as the central control manager and offering remote power monitoring via Web interface or SNMP trap and SNMP monitoring, the manager can get the PoE devices status and alert immediately. The PoE IP cameras could also be controlled remotely, which increases the administrator management efficiency and improve the productivity.
Ordering Information
FGSW-2620PVM 24-Port 10/100Mbps +2 Gigabit TP/SFP Combo Managed PoE Switch

Key Features

Physical Port
• 24-Port 10/100Mbps Fast Ethernet ports with PoE Injector
• 2 10/100/1000Mbps TP and SFP shared combo interfaces
• RS-232 male DB9 console interface for Switch basic management and setup
• Reset button for system management

Power over Ethernet
• Complies with IEEE 802.3af Power over Ethernet End-Span PSE
• Up to 24 IEEE 802.3af devices powered
• PoE Power up to 15.4 Watts for each PoE port
• Auto detect powered device (PD)
• Circuit protection prevent power interference between ports
• Remote power feeding up to 100m
• PoE Management
　–Total PoE power budget control
　–Per port PoE function enable/disable
　–PoE Port Power feeding priority
　–Per PoE port power limit
　–PD classification detection

Layer 2 Features
• Complies with the IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z Gigabit
　Ethernet standard
• Supports Auto-negotiation and Full-Duplex / Half-Duplex modes for all 10Base-T
　/100Base-TX and 1000Base-T ports
• Auto-MDI/MDI-X detection for each RJ-45 port
• Prevents packet loss Flow Control:
　–IEEE 802.3x Pause Frame flow control for Full-Duplex mode
　–Back-Pressure Flow Control in Half-Duplex mode
• High performance of Store-and-Forward architecture, runt/CRC filtering eliminate
　erroneous packets to optimize the network bandwidth
• Broadcast / Multicast / Unicast storm control
• 8K MAC address table, automatic source address learning and ageing
• VLANs
　–IEEE 802.1Q Tag-based VLAN
　–Port-Based VLAN
　–Q-in-Q tunneling
　–Up to 255 VLANs groups, out of 4041 VLAN IDs
• Link Aggregation
　–up to 13 trunk groups
　–up to 8 ports per trunk group with 1.6Gbps bandwidth (Full Duplex Mode)
　–IEEE 802.3ad LACP (Link Aggregation Control Protocol)
　–Cisco ether-channel (Static Trunk)
• Spanning Tree Protocol
　–STP, IEEE 802.1D (Classic Spanning Tree Protocol)
　–RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
• Port Mirroring to monitor the incoming or outgoing traffic on a particular port

Quality of Service
• 4 priority queues on all switch ports
• Traffic classification:
　–IEEE 802.1p CoS
　–IP TOS / DSCP to 802.1p priority mapping
　–Port-Based priority
• Strict priority and Weighted Round Robin (WRR) CoS policies
• QoS and In / Out bandwidth control on each port

Multicast
• IGMP Snooping v1 and v2
• IGMP Snooping v2 fast leave
• Querier mode support

Security
• IEEE 802.1x Port-Based network access control protocol
• RADIUS users access authentication
• L2 / L3 / L4 Access Control List (ACL)
• MAC Filtering and Source IP-MAC / Port-Binding
• Port Security for Source MAC address entries filtering

Management
• Switch Management Interface
　–Console / Telnet Command Line Interface
　–Web switch management
　–SNMP v1, v2c switch management
　–SSL switch management
• DHCP client for IP address assignment
• Built-in Trivial File Transfer Protocol (TFTP) client
• Firmware upgrade via TFTP or HTTP
• Configuration upload / download via TFTP or HTTP
• Four RMON groups 1, 2, 3, 9 (history, statistics, alarms, and events)
• SNMP trap for interface Link Up and Link Down notification
• Ping function
Ordering Information
FGSW-2620PVM 24-Port 10/100Mbps +2 Gigabit TP/SFP Combo Managed PoE Switch

Specification

Hardware Specification
10/100Mbps Copper Ports 24 10/ 100Base-TX RJ-45 Auto-MDI/MDI-X ports
1000Mbps Copper Ports 2 10/100/1000Mbps RJ-45 Auto-MDI/MDI-X ports
SFP/mini-GBIC Slots 2 1000Base-SX/LX, shared with Port-25~Port-26
Switch Architecture Store-and-Forward
Switch Fabric 8.8Gbps / non-blocking
Switch Throughput 6.547Mpps @64Bytes
Address Table 8K entries
Share Data Buffer 512Kbytes
Maximum Frame Size 9K Bytes
Flow Control Back pressure for Half-Duplex
IEEE 802.3x Pause Frame for Full-Duplex
LED Power, FAN Alarm
Link/Activity (Green)
PoE In-Use (Amber)
1000 LNK / ACT(Green)
10/100 LNK / ACT(Green)
Reset Button < 5 sec: System reboot
> 5 sec: Factory Default
Dimension (W x D x H) 440 x 265 x 44 mm, 1U height
Weight 3.6kg
Power Requirement 100~240V AC, 50-60 Hz
Power Consumption / Dissipation 210 Watts maximum / 717 BTU/hr maximum
Power over Ethernet
PoE Standard IEEE 802.3af Power over Ethernet / PSE
PoE Power Supply Type End-Span
PoE Power Output Per Port 48V DC, 350mA . Max. 15.4 Watts
Power Pin Assignment 1/2(+), 3/6(-)
PoE Power Budget 190 Watts
Max. number of Class 2 PD 24
Max. number of Class 3 PD 12
Layer 2 Function
Management Interface Console, Telnet, Web Browser, SSL, SNMPv1, v2c
Port Configuration Port disable/enable
Auto-negotiation
10/100/1000Mbps full and half duplex mode selection
Flow Control disable / enable
Bandwidth Control Ingress / Egress Rate Control
Allow to configure per 128Kbps
VLAN IEEE 802.1Q Tag-based VLAN
Port-based VLAN
Q-in-Q tunneling
Up to 255 VLANs groups, out of 4041 VLAN IDs
Link Aggregation Static Port Trunk
IEEE 802.3ad LACP (Link Aggregation Control Protocol)
Supports 13 groups of 8-Port trunk support
Quality of Service Traffic classification based on :
-Port priority
-802.1p priority
-DSCP/TOS field in IP Packet
IGMP Snooping IGMP (v1/v2) Snooping, up to 256 multicast Groups
IGMP Querier support
Port Mirror RX / TX / Both
1-to-1 mirroring
Security IEEE 802.1x Port-Based Network access control
Port Security
Static MAC
MAC Filtering
MAC / IP Binding
Access Control List IP-Based Layer 3 / Layer 4 ACL
Up to 220 ACL rule entries
SNMP MIBs RFC-1213 MIB-II
RFC-2863 Interface MIB
RFC-2665 EtherLike MIB
RFC-1493 Bridge MIB
RFC-2819 RMON MIB (Group 1, 2, 3,9)
POWER-ETHERNET-MIB
Standards Conformance
Regulation Compliance FCC Part 15 Class A, CE
Standards Compliance IEEE 802.3: 10Base-T
IEEE 802.3u: 100Base-TX
IEEE 802.3z: 1000Base- SX/LX
IEEE 802.3ab: 1000Base-T
IEEE 802.3x: Flow Control
IEEE 802.3ad: Port trunk with LACP
IEEE 802.1D: Spanning tree protocol
IEEE 802.1w: Rapid spanning tree protocol
IEEE 802.1p: Class of service
IEEE 802.1Q: VLAN Tagging
IEEE 802.1x: Port Authentication Network Control
IEEE 802.3af: Power over Ethernet
Environemmental
Operating
Temperature: 0 ~ 50 Degree C
Relative Humidity: 20 ~ 95%
Storage
Temperature: -10 ~ 70 Degree C
Relative Humidity: 20 ~ 95% (non-condensing)
Ordering Information
FGSW-2620PVM 24-Port 10/100Mbps +2 Gigabit TP/SFP Combo Managed PoE Switch

Download

Datasheet

Date Version Description Download
2013-04-19 1.0 FGSW-2620PVM

Firmware

Date Version Description Download
2010-03-05 1.20 Bug Fixed-
1. Fix Switch panel location in Web UI
2. Fix Power Allocation could not display correct power consumption of the support POE power class PD device.

Quick Guide

Date Version Description Download
2009-09-14 1.1 Quick Install Guide
2009-05-20 1.0 Quick Install Guide

User's Manual

Date Version Description Download
2012-04-13 2.4 Function Added: Port description, Users configuration, Configuration Backup without IP(Web only), PoE limit-mode...
2010-04-09 2.3 Add new model's content.
2009-09-14 1.2 User's Manual
2009-05-20 1.1 User's Manual
2009-05-20 1.0 User's Manual

EC Declaration

Date Version Description Download
2009-10-30 1.0 EC Declaration
Ordering Information
FGSW-2620PVM 24-Port 10/100Mbps +2 Gigabit TP/SFP Combo Managed PoE Switch

Related Products

Photo Model Description
ICA-2200 Full HD PoE Box IP Camera
ICA-2500 5 Mega-Pixel PoE Box IP Camera
ICA-3350V 3 Mega-Pixel Vari-Focal Bullet IR IP Camera
ICA-5350V 3 Mega-Pixel Vandal Proof IR IP Camera
ICA-HM101 2 Mega-Pixel PoE Cube IP Camera
ICA-HM126 H.264 Full HD Box IP Camera
ICA-HM127 3 Mega-Pixel H.264 Box IP Camera
ICA-HM131 H.264 Full-HD Fixed Dome IP Camera
ICA-HM132 H.264 2 Mega-Pixel 20M IR Vari-Focal Dome IP Camera
ICA-HM136 H.264 2 Mega-Pixel 20M IR Vandal Proof Dome IP Camera
ICA-HM312 2 Mega-Pixel 25M IR Outdoor Bullet PoE IP Camera
ICA-HM351 2 Mega-Pixel 35M IR Outdoor Box PoE IP Camera
ICF-1700 Touch Screen Internet Multimedia Phone
MGB-Series Transceiver 1000Base-SX/LX SFP Transceiver
POE-152S IEEE 802.3af Power over Ethernet Splitter
POE-162S IEEE 802.3at Gigabit High Power over Ethernet Splitter
POE-E101 IEEE 802.3af Power over Ethernet Extender
POE-E201 IEEE 802.3at Power over Gigabit Ethernet Extender
VIP-256PT 802.3af PoE SIP IP Phone
VIP-360PT Enterprise PoE IP Phone
VIP-560PT Professional PoE IP Phone
WNAP-1120PE 802.11n Wireless Access Point with PoE
WNAP-C3220 300Mbps 802.11n Wireless Ceiling Mount Range Extender
Ordering Information
FGSW-2620PVM 24-Port 10/100Mbps +2 Gigabit TP/SFP Combo Managed PoE Switch